|
Modbo 4.0 Diagrams
PS2 Modbo 4.0 / Modbo 750 / Modbo 760 / Modbo 745 mod chip Installation - ( Version 18 )
SCPH 90002 / SCPH 90001 / SCPH 90000 / SCPH 90003 / SCPH 90004 / SCPH 90006
Ground yourself properly before beginning the install of your new Playstation 2 Modbo 4.0 modchip.
First remove any dust from Playstation 2 main board by gently brushing with fine dry brush or with compressed air.
Then use the Isopropyl alcohol swabs to clean main board Modbo 4.0 NEW mod chip contact points.
Playstation 2 Modchip installation is "Connect The Dots" eg. Point 'A' on Modchip connect by 1 wire to Point 'A' on PS2 Main Board etc.
Scratch "Via" Points with fine pointer gently to expose Gold color then apply flux to 'via' and wire for strong connection.
Place Modbo 4.0 Chip close to Power & Ground / Earth Points using Multi Strand (thick) wire for Ground / Earth & Power Rails & single strand wire for rest.
» » Finish installation with Electrical Insulation tape over chip and tape wires down away from screw holes .
| PLAYSTATION 2 MODBO 4.0 - ( MODBO 745 - MODBO 760 + AU 1.00 ) |
1-9 PCS |
10-19 PCS |
20-49 PCS |
50-99 PCS |
100+ PCS |
AU 11 |
AU 10 |
AU 9 |
AU 8 |
AU 7 |
Playstation 2 ( PS2 ) Modchip List " All PS2 Models " Click Here
The optional points above: "CX" and "F" only need to install them if your modchip has these pads -
The point : "Z" - Modbo 760 and other ps2 chip is not required ( for gameshark only )
For Ground (GND)and 3.3V use thicker wire.
PS2 - Modbo 4.0 . Modbo 745 . Modbo 750 . Modbo 760 . Installation SCPH 90002 .
Modchip-wizard.com Australia : Free quotes for all PS2® repairs / Playstation® 2 SCPH-90003 . SCPH 90004 installations
Version 3 PS2 SCPH-30002 / SCPH 30001
Version 4 PS2 SCPH-30000 / SCPH 30003
Click Diagram to Enlarge
Installation Diagrams for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Click Diagram to Enlarge
Install Diagram for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Version 5 PS2 SCPH-30002R / SCPH 30001
Version 7 PS2 SCPH-39002 / SCPH 39001
Click Diagram to Enlarge
Installation Diagrams for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Click Diagram to Enlarge
Install Diagram for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Version 9 PS2 SCPH-50002 / SCPH 50001
Version 10 PS2 SCPH-50002 / SCPH 50001
Click Diagram to Enlarge
Installation Diagrams for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Click Diagram to Enlarge
Install Diagram for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Version 12 / V13 PS2 SCPH-70002 / SCPH 70001
Version 12 / V13 PS2 SCPH-70002 / SCPH 70001
Click Diagram to Enlarge
Install Diagrams for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Click Diagram to Enlarge
Install Diagram for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Version 12 / V13 PS2 SCPH-70004 / SCPH 70003
Version 14 PS2 SCPH-75002 / SCPH 75001
Click Diagram to Enlarge
Install Diagrams for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Click Diagram to Enlarge
Install Diagram for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Version 14 PS2 SCPH-75004 / SCPH 75003
Version 14 PS2 SCPH-75002 / SCPH 75001
Click Diagram to Enlarge
Install Diagrams for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Click Diagram to Enlarge
Install Diagram for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Version 15 PS2 SCPH-77004 / SCPH 77003
Version 15 PS2 SCPH-77002 / SCPH 77001
Click Diagram to Enlarge
Install Diagrams for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Click Diagram to Enlarge
Install Diagram for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Version 18 PS2 SCPH-90002 / SCPH 90001
Version 16 PS2 SCPH-79002 / SCPH 79001
Click Diagram to Enlarge
Install Diagrams for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Click Diagram to Enlarge
Install Diagram for Modbo 4.0, Modbo 750, Modbo 760
NTSC & PAL
( S=SX / RST=RESET - R / GND=GROUND-EARTH / CX is Optional)
Install Diagram for PS2 Modbo Version 12 SCPH 70002 LASER FIX DIODE
www.modchip-wizard.com » Australia
Soldering for these SCPH 90000 - SCPH 90001 - SCPH 90003 - SCPH 90004 * Series Model Playstation 2 :
The Solder Points on Playstation 2 Main Board are extremely Fine - Ground Yourself Properly Before you Begin !!!
Use Flux to ensure easy and solid connection
Use Thicker Wire for GND - GROUND and 3.3V / 5V - POWER to ensure Continuous Power
Double Check all PS2 Mod chip Bridge wires for correct and solid connection before powering on the console to test.
PS2 Main boards List :
GH-032-13
GH-017
GH-022
GH-023
GH-026
GH-027
GH-032-XX
GH-032-13
GH-037-01
GH-051-51
GH-051-02
GH-006
GH-007
GH-010
GH-015
GH-019
GH-037-01
GH-032-13
GH-037-02
GH-051-02, GH-051-51
GH-037-01, GH-037-02, GH-040-11, GH-040-12, GH-040-51, GH-041-04, GH-041-14,
GH-041-33, GH-041-34, GH-040-52, GH-040-72
GH-032-13, GH-032-24, GH-032-32, GH-035-42,
GH032-44, GH-035-43, GH-032-64
GH-035-11, GH-035-21, GH-035-22, GH-035-31, GH-035-41, GH-035-61, GH-035-71
GH-032-11, GH-032-12, GH-032-21, GH-032-22, GH-032-31, GH-035-4GH-027, GH-029
GH-070-42 . GH-071-42 .
Optional Z wire added for Modbo 760
It can support AR Max and Gameshark if solder Z point.
It can't support AR Max & Gameshark if without Z wire
Modbo 4.0 MAIN FEATURES
AUTOMATIC SELECTION for PS2/PS1/DVD SUPPORTS. (Just insert any disc and modbo 4.0 chip play it !!)
- Modbo 4.0
DVD Region Free Incorporated !! ( to play all regions DVD without need of any extra operation.)
Full 512 Kb Flash Memory on board modbo 4.0
Modbo 4.0 Compatible with Playstation 2 USA/PAL/Japanese -V1,V2,V3,V4, V5, V6, V7, V8, V9, V10,V11,V12,V13, V14-V16 7500X .
Modbo 4.0 is Jumper less (Automatic Version detection)
Easy to Install. (only 18 wires for V1-V8 and 20 wires for V9, V10, V11, V12,V13,V14) If you solder those
10 point on PS2 mainboard directly, can less 10 wire, to help installation faster and easier.
modbo 4.0 IC based 3.3V for enhanced stability
AUTOMATIC "MACROVISION=OFF" ON ALL PS2 FROM V1 TO V14 WITHOUT ADDITIONAL WIRES !!
modbo 4.0 has AUTOMATIC "GREEN FIX" (No more need to change the cable to see your DVD movies on the PS2!!)
- modbo 4.0 Infinity Manager features:
Import Games Fix (All PSX import games are played at FULL SCREEN and FULL COLOR !!)
- Sleep-Mode (The Modchip will switch off itself after boot)
- 100% NO SWAP (Direct boot for all the PS2 and PSX games)
- Supports games on DVD-9 media !!
- PLAYS ALL THE CD’S and DVD’S Games (both, Import or Backup’s)
- modbo 4.0 SUPPORTS MULTI-DISK GAMES !!
- modbo 4.0 SUPPORTS DVD RL GAMES!!
- modbo 4.0 SUPPORTS ANTI-MOD PS1 GAMES !! (Only for V9 - V14 PS2)
- modbo 4.0 SUPPORTS HD COMBO.
- modbo 4.0 SUPPORTS Dev1 and Dev2 .
- SUPPORTS DATEL 16MB MEMORY CARDS and Neo MEMORY CARD !! (No need anymore to use the swap CD!!)
- modbo 4.0 Very Reliable (All the Modchips are 100% tested before delivery)
- modbo 4.0 Very Stable (Thanks to the sleep mode the IC will never Overheat)
- modbo 4.0 CD Lens Safe (Avoid CD lens damage by sending un-necessary signal to the Drive Controller)
Q.
Dear Sir I have a Sony playstation 2 (SCPH-79004) with board GH-062-02 and I want to modify it to play free games, boot on import, backups, ntsc, pal games. Iread that there are a lot of (mod)chips available (e.g. Infinity 1.88) but I don't know the differences between them. Please can you explain me what kind op chips are available for my board and what are the differences between them. Can you also give me the price of this chip and the pictures how to install the chip on the board. Is themodification directly active when the chip is soldered on the board or must the chip be programmed/updated by myself (I expect that the FPGA is pogrammed)? Regards M. Swarzkopff
A. Hello Sir
For Playstation 2 Models : SCPH 79000 Series and SCPH 90000 Series -SCPH 79000 . SCPH 79001 . SCPH 79002 . SCPH 79003. SCPH 79004 . SCPH 79005 . SCPH 79006 .
There are Many Fine Modchips for Playing all region Discs from Japan USA and Europe and Australia and Asia as well as Playing Safety Copies or Backups of Games Discs and Making The PS2 DVD Player as DVD Region Free to allow any Region DVD Play.
There is no Need to Buy Chips such as DMS and other expensive PS2 Chips - as the chips in the Lists below are Manufactured Very High Quality and perform these tasks exactly the same.
Some of the More Popular Chips Include:
By Modbo Team - Modbo.com - Modbo2.com
Modbo 4.0
Modbo 750
Modbo 760
Modbo 745
By Mars Team - By M7 Team - By M-Chip Team
Mars Pro GM-816HD
Mars Pro GM-806
Mars M-Chip M7 GP 788XL
M7 MP 788XL
M7 GP 688
M-Chip M7 MP 688
By Messiah Team
Messiah 2 Chip
Messiah
Messiah 3.7 Chip
Messiah 3.9 Chip
By Matrix Infinity
Matrix Infinity Chip
By Apple Team
Apple 75K Chip
Apple PRO Chip
Apple 75K+ Upgradeable Chip
Apple 75K Mini
1. Yes . The modification is directly active when the chip is soldered on the board.
2. Although the FPGA is pogrammed on Most PS2 Chips and work 100% - Most can also be reprogrammed with a Different or More Suitable operating Bios with Different Features.
3. Some Modchips use a 5Volt Power Rail and Some Modchips a 3.3V Power Rail- Some use different Chips in Manufacturing and Some teams Use their own operating Bios or Lend other Team Bios for their Hardware Chips
example: Modbo mainly use
Matrix Infinity 1.83 Bios .
Matrix Infinity 1.88 Bios .
Matrix Infinity 1.91 Bios .
Matrix Infinity 1.93 Bios .
Matrix Infinity 1.99 Bios .
Toxic Bios is Flashed on Some Batches of Modbo 4.0 NEW Version.
These Variables will end up having different effects on different Model Playstation 2 in terms of Reliability . Stability . Boot Times . Extra Wear and Tear .
We are always Glad to recommend Certain Chips for Certain Model Playstation 2 Consoles after using and Testing many PS2 Chips and Ps2 Console Types.
For Your Model SCPH 79004 : We Recommend and Use:
Modbo 4.0
Modbo 750
Modbo 745
Mars Pro HD
M-Chip M7
Matrix Infinity
But our greatest Recommendation is Matrix Infinity and Second Best is Mars Pro HD and then the Modbo Chips.
We Hope this answers your Questions Clearly
Thank you . Modchip-Wizard
Website: www.blade.cc
www.modchip-wizard.com »
Email: fix@modchip-wizard.com
Legal Disclaimer: Modchip Wizard is a Trademark od Waheroa Modchips Brisbane Australia - Brisbane Modchip wizard is a US mod chip suppliers of modbo 4.0 ps2 mod modbo 750 ps2 mods modbo 745 playstation modchips modbo 760 playstation 2 modchip kits for ps2 ps3 xbox xbox360 wii gamecube in Brisbane Australia- these modbo 4.0 mod chips are not sold to play copied illegal games - ps2 modbo 750 mods playstation 2 modbo 4 mod chips are installed to play lawful games and developement software - all Modchip wizard Brisbane Australia PS2 Playstation 2 Nintendo wii and Gamecube mods Xbox modchip and xbox 360 mods are sold in kit form with warranty from factory. modchip-wizard mods are not supported by SONY SCEA Nintendo Australia & Microsoft Playstation 3 PS2 Playstation 2 Xbox Wii PS3 Xbox 360 are registered trademarks of these companies.
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
