modchip-wizard.com

Matrix Infinity Diagrams

 

 

 

 

 

 

 

PS2 MATRIX INFINITY /MODBO 745 - MODBO 760 DIAGRAMS

 

 

 

 

PS2 Mod chip installation is "Connect The Dots" eg. Point 'A' on Modchip connect by 1 wire to Point 'A' on PS2 Main Board etc.   Ground yourself properly before beginning the install of your new Playstation 2 Matrix Infinity or Modbo 745 mod chip and FOCUS on this Project. Remove any dust from Playstation 2 main board by gently brushing with fine dry brush or compressed air. Use the Isopropyl alcohol swabs to clean main board Modbo 4.0 NEW mod chip contact points. Scratch "Via" Points with fine pointer gently to expose Gold color then apply flux to 'via' and wire for strong connection. Place Matrix Infinity or Modbo 745 Chip close to Power & Ground Points using Multi Strand (thick) wire for Ground / Earth & Power Rails & single strand wire for rest.       PLAYSTATION 2 MODEL NUMBERS AND PS2 CONSOLE TYPES PLAYSTATION 2 LASER PROTECTION - LASER FIX PS2 MODBO MATRIX INFINITY - SETUP MENU / MANAGER CONTACT US / ORDERS BACK TO BLADE.CC HOMEPAGE       » » Finish installation with Electrical Insulation tape over chip and tape wires down away from screw holes

 

 

Download Nintendo Wii Games Download Nintendo Wii games free

 

 

 

 

 

 

 

Modchip-wizard™ Game console mods

 

 

 

Modchip-wizard™ Mod Chips & Repairs

 

 

 

 

modchip-wizard™ Brisbane 0405 080 644

 

modchip-wizard™ Sydney 0405 066 615

 

modchip-wizard™ Melbourne 0433 481 775

 

 

 

 

EMAIL : MODS@BLADE.CC

Playstation 2 ( PS2 ) Modchip List " All PS2 Models " Click Here

Modbo 745 - Matrix Infinity Installation diagram




PS2 Version 1 SCPH 30001

Modbo 760 Install Diagrams PS2 Version 1 SCPH-30001

Matrix Infinity - Modbo 745 diagram




PS2 Version 2 SCPH 30001

Modbo 760 Install Diagrams PS2 Version 2 SCPH-30001

Matrix Infinity Install diagrams






PS2 Version 3 SCPH 30002


Modbo 745 Install Diagram


PS2 Version 3 SCPH-30002

Matrix Infinity Install pictures


PS2 Version 4 SCPH 30002






Modbo 745 Installation Diagrams


PS2 Version 4 SCPH-30002

Modbo 745 Installation guides



PS2 Version 5 SCPH 30002R






Infinity 1.99 Install Diagrams



PS2 Version 5 SCPH-30002R

Matrix Infinity Install diagrams


PS2 Version 7 SCPH 39002








Modbo 745 Install Diagrams


PS2 Version 7 SCPH-39002

PS2 Matrix Infinity Installation diagram


Modbo 745 Diagrams




PS2 Version 9 SCPH 50002








Modbo 760 Install Diagrams



PS2 Version 9 SCPH-50002

Playstation 2 Modbo 745 & Matrix Infinity


Install diagram for PS2 Version 10 SCPH 50002











Modbo 760 Install Diagrams




PS2 Version 10 SCPH-50002

Playstation 2 Matrix Infinity Installation diagrams






Modbo 760 installation for PS2 Version 12 SCPH 70002




Modbo 745 Install Pictures PS2 Version 12 SCPH-70002

Modbo 760 / Matrix Infinity Installation diagram





PAL PS2 Version 14 SCPH 75002








Modbo 745 Installation Pictures






PS2 Version 14 SCPH-75002

Matrix Infinity / Modbo 760 Installation diagram




PS2 Version 14 SCPH 75002










Modbo 745 Installation Pictures




PS2 Version 14 SCPH-75002

Matrix Infinity PS2 Installation pictures




Version 14 SCPH 75002







Modbo 745 Install Pictures




PS2 Version 14 SCPH-75002

Installation Guide


PS2 Infinity Version 14 SCPH 75002







Modbo 745 Installation Diagram



PS2 Version 14 SCPH-75002

PS2 Matrix Infinity Install diagrams




Version 14 75001 . 75001. 75002 . 75003 . 75004 .

Install Matrix Infinity


PS2 Version 14 SCPH 75004







Modbo 530 / Modbo 745 Install Diagram



PS2 Version 14 SCPH-75002

Installation Matrix Infinity



PS2 Version 16 SCPH 79002







Modbo 735 Install Diagrams




PS2 Version 16 SCPH-79002

Installation Diagrams Matrix Infinity




PS2 Version 18 SCPH 90002







Modbo 745 Installation Diagrams




PS2 Version 18 SCPH-90002

www.modchip-wizard.com

Soldering for these MATRIX iNFINITY MODCHIPS FOR ALL * Series Model Playstation 2 :

The Solder Points on Playstation 2 Main Boards are extremely Fine - Ground Yourself Properly Before you Begin !!!

Use Flux to ensure easy and solid connection

Use Thicker Wire for GND - GROUND and 3.3V / 5V - POWER to ensure Continuous Power

Double Check all PS2 Mod chip Bridge wires for correct and solid connection before powering on the console to test.

Q.

 


Myself dealing with modchip installs on the ps2 and wii.



I have a problem, that you might be able to answer based on your
experience. I would be glad if you can direct me towards a solution.



So, recently I have had several ps2 systems (all slims, 7000x and
7700x) that upon installing a modbo 4 or modbo 760 chip despite
checking all soldering points, also for shortcuts, refuse to display
anything on the screen. They boot up, the vent starts spinning, and the
dvd drive also seeks for a disc, the laser turns on, etc, everything
works, but there's nothing to display. I have checked it on several
tv's nothing. checked the cable too with other ps2-s, it's fine.



This is the 3rd system that I have encountered this glitch, and
it's a pain in the ass. Also, when I remove the chip completely the ps2
still does not show anything on the screen.



Do you have any idea what could have gone wrong? Is there anything
I can do to solve it? Or I just need to buy an other ps2 to replace
this one? (I hope not, again...)



Any idea would be welcome, and I thank you for your time in advance.




Best regards,

A fellow modder 
 

A. Hello Sir

For Playstation 2 Models : SCPH 70003 Series and SCPH 75004 Series - and SCPH 77003 Series -

Hello !!

From a Rational point of view- there is remaining a short on the board- ei a small bridge on 2 points likely the bios chip area- - check MNOP and QTUVRW and carefully use solder braid to resoak / clean the area and try again.

From a non rational point of view - a Bridge may not be apparent even by a multi meter but a small amount of too much flux or solder residue might cause a blackscreen so clean also w isoprpyl alcohol.


I have had many black screen and all recovered after careful approach - on 9000 series a short may cause the Fuse to blow on the 5V connection but not on 7 PS2 series.

REPLY:

Hello!!

Thanks for the reply, I know about the BIOS chip shorts, I had one time a short on the modchip itself (modbo 760, M and N points),
that was not apparent. After that I always check for shorts with a multimeter, and use alcohol to clean up the remaining flux. This was not that.

I have found an italian modder website where especially with the 7700x series, where you need to solder onto the '680' (68 ohm resistor bridge) 4 wires for the BIOS,
those resistors tend to blow - even if you keep the iron for a few second there only, and they become not 68 ohm but multi-megaohm valued. Well this happened to me...
I had an old 7000x series slim, which was not working (cause I have lifted some wires off the motherboard accidentally, and anyway the laser assembly I already sold from it)
and it had some of these 680 bridges. Using a heatgun I desoldered some of these and the replaced i on the 7700x. After that everything come back alive.

Lesson learn: do not solder on the legs of the 680 bridges :) It took me severla hours to realize that, as this was the second 7700x that 'gone wrong' like this.

Thanks for your reply by the way!

Regards,
Csaba

PS2 Main boards List :

GH-032-13

GH-017

GH-022

GH-023

GH-026

GH-027

GH-032-XX

GH-032-13

GH-037-01

GH-051-51

GH-051-02

GH-006

GH-007

GH-010

GH-015

GH-019

GH-037-01

GH-032-13

GH-037-02

GH-051-02, GH-051-51

GH-037-01, GH-037-02, GH-040-11, GH-040-12, GH-040-51,

GH-041-04, GH-041-14, GH-041-33, GH-041-34, GH-040-52, GH-040-72

GH-032-13, GH-032-24, GH-032-32, GH-035-42, GH032-44, GH-035-43, GH-032-64

GH-035-11, GH-035-21, GH-035-22, GH-035-31, GH-035-41, GH-035-61, GH-035-71

GH-032-11, GH-032-12, GH-032-21, GH-032-22, GH-032-31, GH-035-4

GH-027, GH-029

Site Map

PS2 Mod-chips Price List

Q.

Dear Sir 


I have a Sony playstation 2 (SCPH-79004) with board GH-062-02 and I want to
modify it to play free games, boot on import, backups, ntsc, pal games. 


Iread that there are a lot of (mod)chips available (e.g. Infinity 1.88) but I
don't know the differences between them.


Please can you explain me what kind op chips are available for my board and
what are the differences between them. Can you also give me the price of
this chip and the pictures how to install the chip on the board. 


Is themodification directly active when the chip is soldered on the board or must
the chip be programmed/updated by myself 


(I expect that the FPGA is pogrammed)?



Regards 

M. Swarzkopff

A. Hello Sir

For Playstation 2 Models : SCPH 79000 Series and SCPH 90000 Series -

SCPH 79000 . SCPH 79001 . SCPH 79002 . SCPH 79003. SCPH 79004 . SCPH 79005 . SCPH 79006 .

There are Many Fine Modchips for Playing all region Discs from Japan USA and Europe and Australia and Asia as well as Playing Safety Copies or Backups of Games Discs and Making The PS2 DVD Player as DVD Region Free to allow any Region DVD Play.

There is no Need to Buy Chips such as DMS and other expensive PS2 Chips - as the chips in the Lists below are Manufactured Very High Quality and perform these tasks exactly the same.

Some of the More Popular Chips Include:

By Modbo Team - Modbo.com - Modbo2.com

Modbo 4.0
Modbo 750
Modbo 760
Modbo 745

By Mars Team -  By M7 Team -  By M-Chip Team 

Mars Pro GM-816HD
Mars Pro GM-806
Mars M-Chip M7 GP 788XL
M7 MP 788XL
M7 GP 688
M-Chip M7 MP 688

By Messiah Team

Messiah 2 Chip
Messiah
Messiah 3.7 Chip
Messiah 3.9 Chip



By Matrix Infinity

Matrix Infinity Chip

By Apple Team

Apple 75K Chip
Apple PRO Chip
Apple 75K+ Upgradeable Chip
Apple 75K Mini




1. Yes . The modification is directly active when the chip is soldered on the board.

2. Although the FPGA is pogrammed on Most PS2 Chips and work 100% - Most can also be reprogrammed with a Different or More Suitable operating Bios with Different Features.

3. Some Modchips use a 5Volt Power Rail and Some Modchips a 3.3V Power Rail- Some use different Chips in Manufacturing and Some teams Use their own operating Bios or Lend other Team Bios for their Hardware Chips

example: Modbo mainly use

Matrix Infinity 1.83 Bios .
Matrix Infinity 1.88 Bios .
Matrix Infinity 1.91 Bios .
Matrix Infinity 1.93 Bios .
Matrix Infinity 1.99 Bios .

Toxic Bios is Flashed on Some Batches of Modbo 4.0 NEW Version.
 
 

These Variables will end up having different effects on different Model Playstation 2 in terms of Reliability . Stability . Boot Times . Extra Wear and Tear .

We are always Glad to recommend Certain Chips for Certain Model Playstation 2 Consoles after using and Testing many PS2 Chips and Ps2 Console Types.




For Your Model SCPH 79004 : We Recommend and Use:


Modbo 4.0
Modbo 750
Modbo 745


Mars Pro HD
M-Chip M7


Matrix Infinity

But our greatest Recommendation is Matrix Infinity and Second Best is Mars Pro HD and then the Modbo Chips.

We Hope this answers your Questions Clearly

Thank you . Modchip-Wizard



Website: www.blade.cc

Modchip-wizard™ Game console mods

Modchip-wizard™ Mod Chips & Repairs

modchip-wizard™ Brisbane 0405 080 644

modchip-wizard™ Sydney 0405 066 615

modchip-wizard™ Melbourne 0433 481 775

EMAIL : MODS@BLADE.CC

Legal Disclaimer: Modchip Wizard is a Trademark od Waheroa Modchips Brisbane Australia - Brisbane Modchip wizard is a modchip supplier of pstwo Matrix Infinity mod pstwo mods pstwo Infinity mod chips pstwo matrix infinity bios mod chip kits for ps2 ps3 xbox xbox360 wii gamecube in Brisbane Australia- these pstwo modchips are not sold to play copied illegal games - pstwo mods pstwo mod chips are installed to play lawful games and developement software - all Modchip wizard Brisbane Australia PS2 Playstation 2 Nintendo wii and Gamecube mods Xbox modchip and xbox 360 mods are sold in kit form with warranty from factory. modchip-wizard mods are not supported by SONY SCEA Nintendo Australia & Microsoft Playstation 3 PS2 Playstation 2 Xbox Wii PS3 Xbox 360 are registered trademarks of these companies.